LS1GTO.com Forums - View Profile: Duckman

Vendors


Go Back   LS1GTO.com Forums > Members List

Duckman Offline

Kollar Racing Products

Visitor Messages

Showing Visitor Messages 1 to 10 of 17
  1. hedgehog
    04-08-2014 06:19 PM
    hedgehog
    Nevermind. I solved my problem.
  2. hedgehog
    03-28-2014 08:32 PM
    hedgehog
    So, remove the three finger flange from the pinion and replace it with the billet plate?
  3. Duckman
    03-28-2014 01:11 AM
    Duckman
    Billet plate bolts to the pinion
  4. hedgehog
    03-27-2014 07:41 PM
    hedgehog
    I was researching driveshaft center support bearings and found a driveshaft on the Koller site that I had a question about. The pn is gtosh1-a and my question is does this shaft connect to the existing pinion flange or does the flange have to be replaced with something else?
  5. DjPhaze
    05-16-2013 01:45 PM
    DjPhaze
    Just got off the phone with you Andy. Thanks for your help. ill be giving you a call very soon. Im thinking of getting a 04-06 GTO LOVELLS ELIMINATOR KIT STOCK HEIGHT very soon.
  6. DjPhaze
    05-16-2013 01:23 PM
    DjPhaze
    Hey Andy. My name is Javier. I think i am a victim of strut rub. I would really appreciate if you would check out my thread on it. Its short. I just started it today. http://www.ls1gto.com/forums/showthread.php?t=520114

    But to make the story short. My front left tire is rubbing when turning hard left. I can also hear it. Its been over 2 years since my last wheel alignment and when i got my alignment done i also had this replaced....

    pedders radius rod bushings
    pedders strut mount bearings
    pedders strut mount bushings

    Can you please help me out and tell me what you recommend i should do? You were recommended to me buy the fellow members on this forum. Thanks
  7. arcenite
    04-28-2012 06:20 AM
    arcenite
    Hey Duckman... Trying to install crossmember mounts. It says to use the thick pads for the GTO but I'm having trouble getting it to line up properly. Is there a reason I can't use the thin mounts?

    Thanks--Bill
  8. Gilligan
    02-23-2012 12:02 PM
    Gilligan
    EDIT: sent a pm
  9. vipboy28
    02-06-2012 08:13 PM
    vipboy28
    Question if im ordering stock height on my springs shocks strut. What size spring pads should i get? 12mm 8mm 6mm?? Or do i even need to replace them? And do i need any other tie aftermarket tierods like pedders?
  10. eng8tophut
    10-08-2011 07:19 PM
    eng8tophut
    While looking for replacements I noticed strut mounts with and without bearings. Other than the obvious what's better for a Saturday nite streetcar? When funds are right I'll buy new stock height struts from KRP but seems silly not replace the mounts at the same time. Silver/ red interior 2006 GTO BONE stock 10,000 miles.

About Me

  • About Duckman
    Location
    Boynton Beach, FL
    Interests
    cars and bikes
    Occupation
    Performance Parts
    gtoowners
    2004 GTO
  • Signature
    THE NORTH AMERICAN DISTRIBUTOR FOR LOVELLS & ROADSAFE PRODUCTS

    NEED TECHNICAL SUPPORT? SUPPORT IS AVAILABLE EVERYDAY 8AM-8PM EST

    631-902-2276
    http://kollarracingproducts.com
    sales@kollarracingproducts.com
    GREAT PARTS, GREAT PRICES, FAST SHIPPING.....

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Yesterday 11:23 PM
  • Join Date: 10-08-2005

Friends

Showing Friends 1 to 3 of 3

All times are GMT -8. The time now is 01:03 AM.




Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2003-2008, LS1GTO.com
Site Banner Design 2005-2007, Cylosoft

LS1GTO.com is not affiliated with General Motors Corp.