LS1GTO.com Forums - Reply to Topic

Vendors


Go Back   LS1GTO.com Forums > GTO Tech > Suspension/Steering/Brakes > rear control arms removal

Thread: rear control arms removal Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now

In order to be able to post messages on the LS1GTO.com Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
07-26-2019 03:08 AM
maradamx3
Quote:
Originally Posted by KM06...View Post
Drop the pipes, drop the plastic fairing (under the trunk) unbolt the rear diff mount, disconnect the sway bar links, disconnect the shocks (good luck on that one), unbolt the spindles, brake calipers and pop line clips, unbolt the outer cv joints, (a loop of wire or zippy around the top of the shock is a way to keep all that from hanging loose) drop the drive shaft, disconnect the toe rods and unplug the ABS pigs (not in that particular order, when you get under there you will figure it out). You will find dropping the sub and calling it a day looks a lot better when you get to the outside bushings; one of those deals that seem like the factory did that first then built the rest of the car around them. If the sub bushings are still factory drop it and replace them. Also if a sway bar upgrade is on the mod list do it with the cradle down, if you try to do it later you will find why you should have done it now. Doing shocks at this time is also not a bad idea; if you can get them off the spindle w/o destroying you will probably not want to go there again, I've had to cut the loop off before and it was still a PITA to get the bushing off the stud. If spring work is in order do it while you have the shocks off for the same reasons Dropping the cradle (IMO) is not kin to selling your soul; maybe I'm just lucky but I've had mine (as well as the front) out twice with no issues. Your results may vary of course.

Mucho trabajo. Didn't have to drop the pipes, fairing, or driveshaft to get mine out. Certainly would make it easier, maybe. Wouldn't recommend trying this on the ground though. Try to find a lift. Much simpler.
07-16-2019 05:53 AM
KM06 Drop the pipes, drop the plastic fairing (under the trunk) unbolt the rear diff mount, disconnect the sway bar links, disconnect the shocks (good luck on that one), unbolt the spindles, brake calipers and pop line clips, unbolt the outer cv joints, (a loop of wire or zippy around the top of the shock is a way to keep all that from hanging loose) drop the drive shaft, disconnect the toe rods and unplug the ABS pigs (not in that particular order, when you get under there you will figure it out). You will find dropping the sub and calling it a day looks a lot better when you get to the outside bushings; one of those deals that seem like the factory did that first then built the rest of the car around them. If the sub bushings are still factory drop it and replace them. Also if a sway bar upgrade is on the mod list do it with the cradle down, if you try to do it later you will find why you should have done it now. Doing shocks at this time is also not a bad idea; if you can get them off the spindle w/o destroying you will probably not want to go there again, I've had to cut the loop off before and it was still a PITA to get the bushing off the stud. If spring work is in order do it while you have the shocks off for the same reasons Dropping the cradle (IMO) is not kin to selling your soul; maybe I'm just lucky but I've had mine (as well as the front) out twice with no issues. Your results may vary of course.
07-10-2019 07:03 PM
MacNav08 Just got my 05 back from my mechanic today. He was swapping out a bent right rear control arm with a used one. He said he thought he was going to have to drop the rear cradle to get that outer bushing bolt out and back in, but he finally managed to get at it without having to. Thank goodness! He's the man....and that's why he's the only one I particularly want working on this car, besides me.

On a related note - it seems that rear control arms for these cars are pretty hard to find. There are no new ones available from GM, and no aftermarket options. Seems salvage yards are the only way to go, which is what we did in this case. Kinda scary....but glad it worked out this time.
06-12-2019 02:31 AM
maradamx3 Really helps to have access to a lift. I had to pry quite a bit to get the outer bushing bolt out and having the car way off the ground was necessary.
06-11-2019 06:09 PM
Glynn It totally smurfing sucks to do them without dropping the cradle. Buy yourself some rear cradle bolts and consider the cost an investment in saving time and grief.
06-11-2019 04:46 AM
LS2-GTO Drop one side of the cradle, unbolt control arm, bolt back in cradle, drop cradle on opposite side, unbolt control arm.
06-10-2019 02:51 PM
floorguy
rear control arms removal

What is the process for removing the rear control arms without totally dropping the rear cradle

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -8. The time now is 08:28 AM.




Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.