LS1GTO Forums banner

FYI, cardboard makes a lousy background for photographs. Buy my stuff anyhow.

Message
139 views 15 replies 5 participants last post by  Slightly.Above.Average  
#1 · (Edited)
$320.00

Check price

Ogden Dunes, Indiana

List of items:

Used fuel pump assemblies, $50 + shipping, ONE available.

New door lock "light" bezels, $20 + shipping, ONE available.

-3 braided stainless brake lines, new or used only for mockup, $20 + shipping per pair, 4 pairs of different lengths available.

New SSTubes 05/06 "front" hardline kit - $60 + shipping

SSTubes intermediate rear line kit - SOLD

exhaust manifold heat shields - just pay shipping.

descriptions for items and additional pictures below.

PLEASE PM ME WITH YOUR ZIPCODE FOR A QUOTE INCLUDING SHIPPING
 
#2 · (Edited)
I have a couple of spare fuel buckets. Their operational condition is unknown. One came out of a fuel tank that I purchased, the other was a spare I picked up on ebay. These would both be suitable if you wanted a bucket to use as a basis for modification, for spare parts, or if you wanted to just slap in a new pump and filter and then send it.

One comes with a float, one does not. Neither have the small rubber bumpers that typically are on the bottom of the bucket to keep them from rattling or wearing against the inside of the tank.

There are a ton of these on ebay all the time, so i've priced them considerably cheaper.

bucket with no float sold

$50 for the bucket with float, not including shipping.


Image


Image
 
#3 · (Edited)
I have some new door handle lock cylinder bezels (also known as a door lock light bezel, although this was an option only on some Australian vehicles). Great if you want to replace your aging, yellowed bezel.

They are still available in Australia, but with the cost of shipping and tariffs (and the fact that Australia has basically suspended all shipping to the US for now), you may not want to or may not be able to get one from there.

$20 each, not including shipping. One remaining.

Image

Image
 
#4 · (Edited)
I have several pairs of -3 AN steel braided brake line.

I have two new, still in packaging lines from Allstar Performance. 12” long, coated, braided stainless, PTFE lined, straight -3 AN ends.

The other three pairs are all Wilwood lines. These are technically used in the sense they were mocked up or used to check sizing, but the ends were not tightened against the fittings and fluid hasn't touched the lining. They are all braided stainless lines with PTFE lining, with straight ends. One pair is 12” long, one is 20”, and the last is 25”.

$20 for a pair, regardless of brand or size, not including shipping.

Kind of a steal for the Wilwood lines, since they be anywhere between 20-40 dollars EACH, new.

Image
 
#5 · (Edited)
I have NEW sets of SSTubes (also known as Fine Lines) front brake caliper hardlines, master cylinder hardlines, and rear intermediate lines (i.e. the small section of brake line that is mounted on each rear control arm), The front hardlines only work with 05/06 vehicles.

Selling the fronts hardlines as a set, and rear intermediates as a pair.

Please note that the line for the driver side caliper is a two piece with an inverted flare coupler. They are also labelled "right" for driver and "left" for passenger for some reason, but they are the correct lines afaik. There are some bends that need to be straightened for installation.

05/06 Front caliper and master cylinder hardlines - $60, not including shipping

rear intermediate lines - SOLD


Image


Image


Image


Image


Image


Image


Image


Image
 
#6 · (Edited)
Lastly I have a pair of these exhaust manifold heat shields. I doubt anyone wants these, but if you do, they are yours. Just pay the shipping costs. They are in decent condition save for one bolt hole one each that is a little enlarged from corrosion.

Just pay shipping costs.

if no one wants them, they get junked next time i make a trip to the yard.

Image


Image


Image
 
#7 · (Edited)
i reserved an extra spot here. oops.
 
#8 ·
I'll take the pump bucket with float as long as fuel level sensor clip is not broken. Sometimes they get damaged when float removed or folded too far

shipping to business 37086
 
#11 ·
it's made with the finest pulp from CHI-nah.

dunno if i'd be wiling to sell.
 
#13 ·
I'll take the:
New SSTubes 05/06 "front" hardline kit - $60 + shipping
SSTubes intermediate rear line kit - $20 + shipping

I feel these are something I'm going to need when I'm ready to do the master cylinder / brake booster swap.
u haz 04 tho, yez?